When installing the blanket, pay particular attention to the liner can not have any wrinkles. Under normal circumstances, blanket + felt it + paper; or blanket + worsted wool + paper. Felt, worsted wool, paper, etc., lining materials, do not care a little, the shop is not easy to wrinkle.
When tensioning the blanket, both sides of the tip and mouth should be carried out at the same time. Do not tighten on one side. Pay attention to safety during operation, avoid inserting the tools and screws into the rollers and rolling off the blanket.
The new blanket has good elasticity and good stretchability. The tensioned blanket should be gradually stretched and tightened once. After the press is pressed for 3~5 minutes, it can be tightened again. This can be achieved by repeated 2 or 3 times of tightening.
Whether the rubber blanket and its liner is flat, if the blanket contains ink and debris, it will appear convex and concave, and it is necessary to reinstall the blanket.
Before the blanket is installed, the blanket thickness of blanket+felt or worsted wool+paper should be accurately measured with a micrometer to hear the micrometer å—’, å—’, å—’, and å—’. Soft lining: blanket+felt+paper, the lining thickness is: 3.35~3.45mm. Neutral lining: blanket + worsted wool + paper or blanket + paper, lining thickness: 3.20 ~ 3.25mm. Hard lining: Blanket + insulating paper or photo paper, with lining thickness of 3.18-3.20mm.
Blanket trimming requires the rectangular shape to be upright, and the desired effect can only be obtained if the warp direction of the blanket is chosen as the direction of cutting, tightening, and pulling. The warp and weft directions can be known by observing the cylinder shape of the natural roll. The direction of the wire parallel to the core line of the natural roll should be the weft direction, and the direction perpendicular to the weft direction wire is the longitudinal direction. Mainly based on the blanket back (back) plain weave fabric to determine silk.
The backing paper in the blanket lining is shorter than the blanket so as to prevent the water from infiltrating the paper fibers from swell and deformation and reduce the rust of the drum.
Blanket is a kind of elastic object. It will produce elongation after stress during the whole process of clamping, transmission and imprinting. In order to relatively accurately transfer the image size on the printing plate to the paper, the blanket is required to have a low elongation during the entire printing process and must be uniform.
The above-mentioned elongation is related to the quality of the blanket itself, and depends on the degree of tightness of the blanket on the drum. The tighter the blanket is, the better it is? This is certainly not the case in practice. The blanket must be stretched tightly and properly.
1 The tighter the blanket is stretched, the lower the elongation during the printing process, and the smaller the size of the graphic. However, if the skin cloth is stretched too tightly, the amount of friction on the plate increases and the plate life decreases.
2 If the blanket is stretched too loosely, then the expansion and contraction rate of the blanket will increase, and the amount of friction on the layout will decrease, which will easily lead to double printing (ghosting).
When installing the blanket, pay particular attention to the liner can not have any wrinkles. Under normal circumstances, blanket + felt it + paper; or blanket + worsted wool + paper. Felt, worsted wool, paper, etc., lining materials, do not care a little, the shop is not easy to wrinkle.
When tensioning the blanket, both sides of the tip and mouth should be carried out at the same time. Do not tighten on one side. Pay attention to safety during operation, avoid inserting the tools and screws into the rollers and rolling off the blanket.
The new blanket has good elasticity and good stretchability. The tensioned blanket should be gradually stretched and tightened once. After the press is pressed for 3~5 minutes, it can be tightened again. This can be achieved by repeated 2 or 3 times of tightening.
Whether the rubber blanket and its liner is flat, if the blanket contains ink and debris, it will appear convex and concave, and it is necessary to reinstall the blanket.
Before the blanket is installed, the blanket thickness of blanket+felt or worsted wool+paper should be accurately measured with a micrometer to hear the micrometer å—’, å—’, å—’, and å—’. Soft lining: blanket+felt+paper, the lining thickness is: 3.35~3.45mm. Neutral lining: blanket + worsted wool + paper or blanket + paper, lining thickness: 3.20 ~ 3.25mm. Hard lining: Blanket + insulating paper or photo paper, with lining thickness of 3.18-3.20mm.
Blanket trimming requires the rectangular shape to be upright, and the desired effect can only be obtained if the warp direction of the blanket is chosen as the direction of cutting, tightening, and pulling. The warp and weft directions can be known by observing the cylinder shape of the natural roll. The direction of the wire parallel to the core line of the natural roll should be the weft direction, and the direction perpendicular to the weft direction wire is the longitudinal direction. Mainly based on the blanket back (back) plain weave fabric to determine silk.
The backing paper in the blanket lining is shorter than the blanket so as to prevent the water from infiltrating the paper fibers from swell and deformation and reduce the rust of the drum.
Blanket is a kind of elastic object. It will produce elongation after stress during the whole process of clamping, transmission and imprinting. In order to relatively accurately transfer the image size on the printing plate to the paper, the blanket is required to have a low elongation during the entire printing process and must be uniform.
The above-mentioned elongation is related to the quality of the blanket itself, and depends on the degree of tightness of the blanket on the drum. The tighter the blanket is, the better it is? This is certainly not the case in practice. The blanket must be stretched tightly and properly.
1 The tighter the blanket is stretched, the lower the elongation during the printing process, and the smaller the size of the graphic. However, if the skin cloth is stretched too tightly, the amount of friction on the plate increases and the plate life decreases.
2 If the blanket is stretched too loosely, then the expansion and contraction rate of the blanket will increase, and the amount of friction on the layout will decrease, which will easily lead to double printing (ghosting).
When tensioning the blanket, both sides of the tip and mouth should be carried out at the same time. Do not tighten on one side. Pay attention to safety during operation, avoid inserting the tools and screws into the rollers and rolling off the blanket.
The new blanket has good elasticity and good stretchability. The tensioned blanket should be gradually stretched and tightened once. After the press is pressed for 3~5 minutes, it can be tightened again. This can be achieved by repeated 2 or 3 times of tightening.
Whether the rubber blanket and its liner is flat, if the blanket contains ink and debris, it will appear convex and concave, and it is necessary to reinstall the blanket.
Before the blanket is installed, the blanket thickness of blanket+felt or worsted wool+paper should be accurately measured with a micrometer to hear the micrometer å—’, å—’, å—’, and å—’. Soft lining: blanket+felt+paper, the lining thickness is: 3.35~3.45mm. Neutral lining: blanket + worsted wool + paper or blanket + paper, lining thickness: 3.20 ~ 3.25mm. Hard lining: Blanket + insulating paper or photo paper, with lining thickness of 3.18-3.20mm.
Blanket trimming requires the rectangular shape to be upright, and the desired effect can only be obtained if the warp direction of the blanket is chosen as the direction of cutting, tightening, and pulling. The warp and weft directions can be known by observing the cylinder shape of the natural roll. The direction of the wire parallel to the core line of the natural roll should be the weft direction, and the direction perpendicular to the weft direction wire is the longitudinal direction. Mainly based on the blanket back (back) plain weave fabric to determine silk.
The backing paper in the blanket lining is shorter than the blanket so as to prevent the water from infiltrating the paper fibers from swell and deformation and reduce the rust of the drum.
Blanket is a kind of elastic object. It will produce elongation after stress during the whole process of clamping, transmission and imprinting. In order to relatively accurately transfer the image size on the printing plate to the paper, the blanket is required to have a low elongation during the entire printing process and must be uniform.
The above-mentioned elongation is related to the quality of the blanket itself, and depends on the degree of tightness of the blanket on the drum. The tighter the blanket is, the better it is? This is certainly not the case in practice. The blanket must be stretched tightly and properly.
1 The tighter the blanket is stretched, the lower the elongation during the printing process, and the smaller the size of the graphic. However, if the skin cloth is stretched too tightly, the amount of friction on the plate increases and the plate life decreases.
2 If the blanket is stretched too loosely, then the expansion and contraction rate of the blanket will increase, and the amount of friction on the layout will decrease, which will easily lead to double printing (ghosting).
When installing the blanket, pay particular attention to the liner can not have any wrinkles. Under normal circumstances, blanket + felt it + paper; or blanket + worsted wool + paper. Felt, worsted wool, paper, etc., lining materials, do not care a little, the shop is not easy to wrinkle.
When tensioning the blanket, both sides of the tip and mouth should be carried out at the same time. Do not tighten on one side. Pay attention to safety during operation, avoid inserting the tools and screws into the rollers and rolling off the blanket.
The new blanket has good elasticity and good stretchability. The tensioned blanket should be gradually stretched and tightened once. After the press is pressed for 3~5 minutes, it can be tightened again. This can be achieved by repeated 2 or 3 times of tightening.
Whether the rubber blanket and its liner is flat, if the blanket contains ink and debris, it will appear convex and concave, and it is necessary to reinstall the blanket.
Before the blanket is installed, the blanket thickness of blanket+felt or worsted wool+paper should be accurately measured with a micrometer to hear the micrometer å—’, å—’, å—’, and å—’. Soft lining: blanket+felt+paper, the lining thickness is: 3.35~3.45mm. Neutral lining: blanket + worsted wool + paper or blanket + paper, lining thickness: 3.20 ~ 3.25mm. Hard lining: Blanket + insulating paper or photo paper, with lining thickness of 3.18-3.20mm.
Blanket trimming requires the rectangular shape to be upright, and the desired effect can only be obtained if the warp direction of the blanket is chosen as the direction of cutting, tightening, and pulling. The warp and weft directions can be known by observing the cylinder shape of the natural roll. The direction of the wire parallel to the core line of the natural roll should be the weft direction, and the direction perpendicular to the weft direction wire is the longitudinal direction. Mainly based on the blanket back (back) plain weave fabric to determine silk.
The backing paper in the blanket lining is shorter than the blanket so as to prevent the water from infiltrating the paper fibers from swell and deformation and reduce the rust of the drum.
Blanket is a kind of elastic object. It will produce elongation after stress during the whole process of clamping, transmission and imprinting. In order to relatively accurately transfer the image size on the printing plate to the paper, the blanket is required to have a low elongation during the entire printing process and must be uniform.
The above-mentioned elongation is related to the quality of the blanket itself, and depends on the degree of tightness of the blanket on the drum. The tighter the blanket is, the better it is? This is certainly not the case in practice. The blanket must be stretched tightly and properly.
1 The tighter the blanket is stretched, the lower the elongation during the printing process, and the smaller the size of the graphic. However, if the skin cloth is stretched too tightly, the amount of friction on the plate increases and the plate life decreases.
2 If the blanket is stretched too loosely, then the expansion and contraction rate of the blanket will increase, and the amount of friction on the layout will decrease, which will easily lead to double printing (ghosting).
Made of stainless steel with eco-friendly PVC rubber paint coating.They are made of sturdy steel with a matte coating to prevent rusting.Hold clothes steadily without worry of them falling down or slipping off.
Smooth & Delicate Surface, well protect your clothes and your hands.Metal hangers are also excellent space savers too due to their flat design. Metal hangers are not only strong and durable, but also they make a chic addition to the closet or retail space.
Garment Hanger,Metal Pvc Coating Black Hangers,Pvc Coating Metal Clothes Hanger,Pvc Coating Metal Hanger
GUILIN LANHOME TRADING CO., LTD. , https://www.guilinlanhome.com