With the wide use of wooden doors, people are paying attention to the installation of wooden doors while maintaining wooden doors. However, what problems should be paid attention to when installing wooden doors? What are the conditions? Summarize some aspects of the wooden door installation.
1. Installation conditions
The wooden door must be installed with a reserved opening. It is strictly forbidden to install the side wall. The wooden door shall be installed after the installation of the groundwork (such as floor tiles and stone) of the hole, and after the wall putty is scraped and polished, the wall shall be covered with wall tiles and the hole at the stone, and all the holes shall be attached to the side of the hole. To perform the installation work.
The wall thickness of the installation wall is 25%. If the humidity is 25%, the moisture barrier should be installed on the installation wall. The installation site is clean, free of clutter, and has no cross-work.
2. Installation tool
Should be prepared with electric hammer, woodworking hoe, plane, flat boring, fine tooth saw (gang saw), screwdriver, square ruler, tape measure, hanging hammer, level ruler, electric drill, hole opener, stamp, corresponding specification drill.
3. Installation sequence
The first step is to assemble the door cover. First find the door cover and the vertical plate. According to the back number, the joints should be on the same plane, and the joints should be glued.
The second step is to install the door cover. Put the assembled door cover into the door hole as a whole, and fix the door cover around with the small wooden strip. The two sides of the door cover should be on the same plane as the wall. Then check whether the whole door cover is perpendicular to the ground. The top cover and the two sides of the door cover Whether the two corners of the board are at right angles, whether the door panel is bent or not, and the iron pieces are twisted at both ends to wrap the wall.
The third step is to install the door leaf. The hinge groove is opened first, and the distance between the hinge groove and the two ends of the door leaf is preferably 1/10 of the height of the door leaf.
The fourth step is to install the door lock. After loading, check whether the door leaf and door lock switch are flexible, whether the seam is flexible, and whether the seam is in compliance with the specifications.
The fifth step is to install the door line. Cut the door line with right-angled edges into a 45-degree angle, trim it with a woodworking planer, insert it into the door pocket at the right angle, and glue the door sleeve wire to the door panel with the floor glue.
In the sixth step, install the door suction at the corresponding position.
4. Wooden door installation skills
When installing the wooden door, first check whether the wooden door components are complete, whether the dimensions of each component are correct, and whether the door is assigned to the corresponding position to match the door hole ruler.
The tips for installing the wooden door are as follows: Please place the goods horizontally on the floor when you want to load the goods. Do not lean on. Painted products should be painted within five days. Try to avoid long-term outdoor sunlight and prevent the wooden door from being heated. Keep indoor air circulation and prevent wooden doors from getting wet frequently. Prevent the wooden door from being subjected to abnormal impact. If it is not closed, it should not be used too hard. It is strictly forbidden to hang heavy objects on the door. Before installing the corner wall and T-wall door, the customer should be notified to make a "false wall" on the side without the threshold. The width is not less than 50mm. According to the width of the line, the width of the "fake wall" is determined. Otherwise, The door edges displayed on both sides are asymmetrical.
5. Supervision of wooden door installation
The installation process of the wooden door is very important. A good wooden door needs to be properly installed to achieve its superior performance. The mouth is consistently good. The door leaf and door lock switch are flexible. The gap between the door and the door is the same. The door sleeve panel should be perpendicular to the ground without bending. The door sleeve line is in close contact with the wall surface. The decorative surface is not damaged. Clean the fully installed solid wood door after installation and teach the user to accept.
Document.body.oncopy = function () { setTimeout( function () { var text = clipboardData.getData("text"); if (text) { text = text + " This article comes from China Wooden Door Network, China's well-known wooden door industry portal Website! (http://) Detailed reference: "+location.href; clipboardData.setData("text", text); } }, 100) }Floating Shaver,Men Trimmer Shaver Rechargeable,Electric Beard Shaver,Professional Fabric Shavers
ZHEJIANG SHENGFA ELECTRIC APPLIAMNCES CO.,LTD , https://www.cn-shengfa.com