Step 1: If you need to clean the tennis court with a high voltage power washer (3000 lbs). Most are not, but some sap or really dirty.
Step 2: Clean, fill and smooth cracks. We use modified concrete to fill them. You can also buy an acrylic patch to fill them.
We like to call it a crack, not a fixed comeback because it cracks almost all cracks. Almost every crack I have seen in tennis courts is whether it is a small crack or a big crack. They are likely to reappear after they are filled/fixed and usually only come back as a small crack. But not all cracks come back. We use quartz sand polymer modified cement to fill in all cracks. Some people use fill cracks, but we find it to be expensive and not effective.
Construction process:
There are more and more grasses or weeds in the cracks that have to be cleaned out and must come out first. (Use a screwdriver or putty knife to scrape them)
The cracks A to V were used to give more concrete surface area to hold. Small hair cracks can be kept as separate surface trims that will fill them in
Mix the cement and pour it into the cracked one. Use 镘 to straighten out the cement. When used, the cement blocks dry to any high point after work.
Step 3: Fix the patch bird acrylic bath or low surface trim or area with some levels. For deep and low areas, we use polymer to modify cement. For different depths in the low zone, you can use some pea gravel to help fill it up. There is an acrylic patch that you can buy that will fill the low area. We just like cement.
Construction process:
1. Clean the surface with a power washer or use a crusher scar to adhere to a better surface.
2. Use 2x4 to spread the cement. Let's face it completely dry before applying it.
Note: We usually trim additional coats on a low surface to help it go smoothly.
Not all areas of the tennis court can be resolved. If the asphalt has sunk causing a bird bath (low area, collect water). Sometimes it can be time consuming and expensive repairs. Therefore, we will put a coat on the surface of the area 2-3 to help build it up.
Step 4: Apply acrylic finish to the tennis court. Mix according to instructions. Different amounts of silica sand will increase the durability of the cleaning and the speed of the ball.
Primer
After all, cracks and low sights are full of our application primer acrylic finishes. Although the base coat is not always necessary. It helps because it contains more surface trimming with colored quartz sand because it has more defects filling in the surface.
The base coat is applied with a squeegee. You must always keep wet.
Tip: Make sure you have enough people to help, so that you have 2 people mixed with a spatula and at least 2 people. Before any of this will cause this product, California is evenly dispersed.
Step 5: Apply two layers of acrylic color.
If you are a coat that does not put down an application base, (not recommended) a color coat, an old tennis court surface is cleaned, ensuring that your power increases the surface of the bond.
This is the most important because it will be the coat that you will see for many years. It is the same way as a primer (with a spatula). Be sure to keep the wet side agitated and enough people for your product.
Step 6: The size of the striped (paint) line supervision.
Painting can be a very time consuming experience. We used tape to map the circuit. Where do we both use the trademark tape? Then we took out about 6-10 feet of tape and marked it with the next line. This helps keep the line as straight as possible. And you can do tennis courts in a few hours.
prompt:
To sell the products, you can paint the colors of the paint before they stop bleeding from the tape. We have found that this is a waist of money and time, as long as the tape is of good quality and it is closed. When you paint not press hard and use 2" brush. There is a person who pours out of paint while another is spreading out. The third person will touch it. This will make sure that you even paint and you will get perfect before it spreads Dry.
Electric Beauty Massage Bed
Our bed managed to combine fashion, practicality with elegance.
Our bed with low noise, long-life and safety motors.
Our bed with first-class PU, the material is comfortable and breathability.
You can use our electric beauty massage bed in beauty salon, plastic surgery hospital, beauty health club and spa.
Our bed with multifunction, can use in facial, massage, manicure, dentist and plastic surgery area.
Why CHAOHUI Electric Beauty Massage Bed is your best choice?
Chaohui Salon Equipment Co., Ltd. engages in developing and manufacturing barber and beauty chairs, beds and other products. Relying on its strong technical force and advanced equipment, the perspicacious company aims at the international and domestic barber and beauty chair and bed market. Provided with a group of experienced designers, the company has been constantly improving the product quality, and developed many new ergonomics-based products, including barber chairs, facial chairs, medical bed,hospital bed,shampoo chairs, beauty chairs, massage chairs, massage beds, etc. The development idea of each product comes from the users; each product is comfortable and durable, which reflects the high-tech quality and strict quality assurance of ChaoHui; and each product has been well received since entering market for its noble and unique style and exquisite workmanship.
Following the [people-oriented" design concept and relying on the advanced production technology and a flow of new designs, the company has been in the forefront of the barber and beauty equipment industry. By the use of its one-stop topping services and first-class quality, ChaoHui has interpreted for the users in modern life that [high quality created high- tasted life".
Electric Massage Bed,Electric Adjustable Bed,Electric Facial Bed,Professional Electric Massage Beds
ChaoHui Beauty Salon Equipment Co., Ltd. , https://www.chaohuibeauty.com